N38 Excessive servo lag in %.2s
N39 Nominal speed value too high %.2s
N41 Standstill monitoring err. in %.2s
N42 Excessive offset in %.2s
N50 Touch point inaccessible
N51 Positioning error
N52 Stylus already in contact
N53 Exchange touch probe battery
N54 Probe system not ready
N17738 Limit switch %.2s+
N56 Limit switch %.2s+
N17739 Limit switch %.2s-
N58 Limit switch %.2s-
N59 FN 14: error code %-3u
N60 Two TOOL DEF %-3u with PGM CALL
N61 Tool table locked
N62 Ref mark %.2s: incorrect spacing
N63 Handwheel?
N109 PLC: excessive nesting
N110 PLC: stack underflow
N111 PLC: stack overflow
N112 PLC: timeout
N113 PLC: CASE out of range
N115 PLC: index range incorrect
N133 PLC: M4005/M4006/M4006 incorrect
N134 PLC: more than one strobe active
N151 MP: line w/o number
N152 MP: incorrect number
N153 MP: separator missing
N154 MP: input value incorrect
N155 MP: defined twice
N156 MP: not defined
N157 MP: saving not possible
N159 Pocket 0 undefined
N160 Wrong pocket number
N937 Wrong pocket number
N161 Feed rate is missing
N162 No new axis during rotatn
N163 Max. tool age expired
N164 Exchange buffer battery
N165 Oriented spindle stop inactive
N166 Tool file?
N167 Datum table?
N168 Error
N938 Key non-functional
N939 Program memory exceeded
N940 Search address missing
N941 Tool number 0 not permitted
N169 Tool number already assigned
N170 Jump to label 0 not permitted
N942 Entry value incorrect
N943 Entry value incorrect
N171 Entry value incorrect
N172 Entry value incorrect
N173 Entry value incorrect
N174 Entry value incorrect
N175 Entry value incorrect
N176 Entry value incorrect
N177 Cycle 27(G127): depth > radius
N178 Entry value incorrect
N179 Entry value incorrect
N180 Blank form definition incorrect
N183 Selected block not addressed
N184 Program not found
N185 Further file entry impossible
N944 Program name already exists
N187 Label number already assigned
N188 Label number %-3u already assigned
N189 Data transfer erroneous
N194 Program incomplete
N196 Interface already assigned
N197 Baud rate not possible
N945 Program data erroneous
N946 Program data erroneous
N200 Ext. in-/output not ready
N201 NC program memory erased
N947 Operating parameters erased
N948 Protected File!
N202 The calling program was changed
N203 Emergency stop defective
N205 Emergency stop PLC
N207 PGM not found
N212 FK reference to current block
N214 Arithmetical error
N215 Arithmetical error
N216 Calculated Q parameter too large
N217 Calculated coordinate too large
N218 Calculated rpm too large
N219 Calculated feed rate too large
N220 Calculated tool number too large
N221 Calculated label no. too large
N222 Calculated error no. too large
N223 Calc. scaling factor too large
N224 Incr. polar angle too large
N225 0 pitch not permitted
N226 Arithmetical error
N227 Arithmetical error in APPR/DEP
N228 Arithmetical error in APPR/DEP
N229 Arithmetical error in APPR/DEP
N230 Arithmetical error in APPR/DEP
N231 Arithmetical error in rough-out
N232 Arithmetical error in CR
N233 Arithmetical error in CT
N234 Arithmetical error in RND/CHF
N235 Incorrect arc/arc intersection
N236 Incorrect arc/line intersection
N237 Incorrect line/line intersection
N238 Arithmetical error in APPR/DEP
N239 Error in radius compensation
N240 Error in contour pocket
N241 Error in contour pocket/train
N242 Error in contour pocket
N243 Error in contour pocket
N244 Error in radius compensation
N245 Error in radius compensation
N246 Error in contour pocket
N247 Error in contour pocket
N250 Arithmetical error during M112
N251 Parameter calculation error
N252 Error while testing limit switch
N253 Path comp wrongly ended
N254 Path comp wrongly started
N255 Path comp wrongly started
N256 Path comp wrongly started
N257 Path comp wrongly started
N258 Path comp wrongly started
N259 Path comp wrongly started
N260 CYCL DEF incomplete
N261 CYCL DEF not defined
N263 0 plunging depth not permitted
N264 User cycle does not exist
N265 Subprogram does not exist
N266 Subprogram does not exist
N272 Incorrect block syntax
N274 Tool definition not permitted
N275 TOOL DEF w/o length or radius
N276 CT after APPR not permitted
N277 CHF after APPR not permitted
N278 RND after APPR not permitted
N279 RND radius = 0 not permitted
N280 Chamfer length = 0 not permitted
N281 2nd rounding arc not permitted
N282 RND after CHF not permitted
N283 CHF after RND not permitted
N284 2nd chamfer not permitted
N285 DEP LCT after HELIX not permittd
N286 APPR LCT before HELIX not permtd
N287 Illegal NC block
N288 Rounding arc not permitted
N289 Rounding arc not permitted
N290 Chamfer not permitted
N291 DEP not last block
N292 No rounding arc as last block
N293 No chamfer as last block
N294 Only one DEP block permitted
N295 DEP not permitted
N296 APPR not permitted
N297 APPR not first block
N299 Cycle 14 (G37) not permitted
N300 Tool call not permitted
N302 M91/M92 with 3DROT not permitted
N303 M114 with 3DROT not permitted
N305 No M114 with radius compensation
N307 Axis double programmed
N308 Axis double programmed
N309 Axis double programmed
N310 Axis double programmed
N311 Axis double programmed
N313 Plane wrongly defined
N314 3-D comp.: plane def incorrect
N315 Plane wrongly defined
N317 Plane wrongly defined
N318 Plane wrongly defined
N319 Plane wrongly defined
N320 Plane wrongly defined
N321 Plane wrongly defined
N322 Plane wrongly defined
N323 Plane wrongly defined
N324 Plane wrongly defined
N325 Plane wrongly defined
N326 Plane wrongly defined
N327 Plane wrongly defined
N328 Plane wrongly defined
N329 Rotary axis not permitted here
N950 Wrong axis programmed
N951 Wrong axis programmed
N330 Locked axis was programmed
N331 Wrong axis programmed
N332 Wrong axis programmed
N333 Wrong axis programmed
N335 Rotary axis not programmed
N337 No rotary axis was programmed
N338 No principal axis was programmed
N339 Slave axis of gantry programmed
N952 Wrong rpm
N340 Wrong rpm
N341 Wrong rpm
N342 Wrong rpm
N343 Wrong rpm
N344 Rpm too high for this cycle
N345 0 rpm not permitted
N346 Wrong rpm
N347 Chamfer not permitted
N348 Chamfer not permitted
N349 Chamfer not permitted
N350 Chamfer not permitted
N351 Chamfer not permitted
N352 Chamfer not permitted
N353 Chamfer not permitted
N354 Chamfer too large
N355 Chamfer too large
N356 Chamfer too large
N357 Circle end pos. incorrect
N358 C-block: arc end pos. incorrect
N359 Circle end pos. incorrect
N360 Circle end pos. incorrect
N361 Circle end pos. incorrect
N362 Label number not found
N363 Label 0 is missing
N364 Label number not found
N365 Cycle 14: LBL not found
N366 Pole is missing
N367 Circle center missing
N368 Tool radius too small
N369 Tool radius 0 not permitted
N370 Radius comp. undefined
N371 Radius comp. undefined
N372 Radius comp. undefined
N373 Radius comp. undefined
N374 Radius comp. undefined
N375 Traverse reference points
N376 Rounding-off undefined
N377 Rounding-off undefined
N378 Rounding-off not permitted
N379 Rounding radius too large
N380 Rounding radius too large
N381 Rounding radius too large
N382 Rounding radius too large
N383 Rounding radius too large
N384 Rounding radius too large
N385 Rounding radius too large
N386 Rounding radius too large
N387 Rounding radius too large
N388 Spindle must be turning
N389 Mirror image on tool axis
N390 Mirror image on tool axis
N391 Tool axis is missing
N392 Tool axis is missing
N393 Tool axis is missing
N394 Tool axis is missing
N395 Tool axis is missing
N396 Tool axis is missing
N397 Tool axis is missing
N398 Tool definition is missing
N400 Tool definition is missing
N401 Tool number is missing
N402 Tool radius too large
N403 Tool radius too large
N404 Tool radius too large
N405 Tool radius too large
N406 Tool radius too large
N407 Tool radius too large
N408 Tool radius too large
N409 Tool radius too large
N410 Tool radius too large
N411 Tool radius too large
N412 Tool radius too large
N413 Program start undefined
N414 Program start undefined
N415 Program start undefined
N416 Program start undefined
N417 Program start undefined
N418 Program start undefined
N419 Program start undefined
N420 Program start undefined
N421 Program start undefined
N422 Program start undefined
N423 Program start undefined
N424 Program start undefined
N425 Cancel comp. before PLC positng
N426 Program start undefined
N953 Block format incorrect
N427 Block format incorrect
N429 Excessive subprogramming
N430 Excessive subprogramming
N432 Excessive subprogramming
N433 Contradictory signs in cycle
N434 Wrong sign programmed
N435 Angle reference missing
N436 Angle reference missing
N437 Radius too small
N438 Angle reference missing
N439 Angle reference missing
N440 DEP interruption not permitted
N441 DEP interruption not permitted
N442 Coordinates after APPR missing
N443 Range exceeded
N444 Faulty range data
N445 Start position incorrect
N446 Time limit exceeded
N447 CYCL parameter incorrect
N448 Oversize greater than depth
N451 Scaling factors not equal
N454 Stylus deflection exceeds max.
N455 Too many subcontours
N456 Too many subcontours
N457 Too many subcontours
N458 Too many subcontours
N459 Too many subcontours
N460 Too many subcontours
N461 Too many subcontours
N462 Too many subcontours
N463 Too many subcontours
N464 Too many subcontours
N465 Too many subcontours
N466 Too many subcontours
N467 Too many subcontours
N468 Too many subcontours
N469 Too many subcontours
N470 Too many subcontours
N471 Too many subcontours
N472 Too many subcontours
N473 Too many subcontours
N474 Too many subcontours
N475 Contour programming error
N477 Contour programming error
N478 Contour programming error
N479 Contour programming error
N480 Contour programming error
N481 Contour programming error
N482 Contour programming error
N483 Contour programming error
N484 Contour too complex
N485 Contour too complex
N486 Contour too complex
N487 Contour too complex
N488 Contour too complex
N489 Contour too complex
N490 Contour too complex
N491 Contour too complex
N492 Contour too complex
N493 Contour too complex
N954 Address letter already assigned
N494 Block too long
N955 G-code group already assigned
N495 Unknown G-code
N496 N-code missing
N497 CMA file: no active line
N500 Too many compensation points
N501 Too many compensation functions
N957 Power interrupted Power interrupted
N958 Relay ext. dc voltage missing Relay ext. dc volt. missing
N859 ERROR
N860 Axis cannot be shown
N861 Further reduction not possible
N862 Further enlargement not possible
N863 BLK FORM cannot be shown
N864 Wrong tool axis in BLK FORM
N865 Tool radius cannot be shown
N888 Text not found
N1086 Too many points
N1097 Tolerance value too great
N1106 Delete entire cycle: DEL!
N1107 Block in cycle not allowed !
N1125 Reference to block %.6s:no DEL
N1126 Deactivate M112
N1141 RL/RR not permitted if M120 = 0
N1142 Radius comp. entry is missing
N1143 Impermissible radius comp.
N1144 R+/R- not permitted with M120
N1145 RND not permitted with M120
N1146 Chamfer not permitted with M120
N1147 Analog voltage not defined
N1148 Analog voltage ambiguous
N1149 Incorrect entry in MP%.4u
N1150 Touch probe not ready %.3s
N1151 Resumption with M120 not allowed
N1154 Illegal name for file or path
N1170 Measuring touch probe selected
N1171 Triggering touch probe selected
N1172 Calibrate touch probe
N1178 3DROT active: use axis buttons
N1182 Incorrect entry in MP%.4u.%u
N1186 File format has changed
N1187 M89 not permitted
N1192 Entered angle not permitted
N1193 TOOL.T: enter number of teeth
N1266 Block format incorrect
N1521 PLC error table not yet compiled
N1523 PLC: no error table selected
N1524 PLC: error table missing
N1525 PLC: error table not .PET
N1527 PLC: error table not found
N1528 PLC: err. table format incorrect
N1568 Wrong axes in .PNT file
N1590 Dist value too small
N1682 TOOL.T: LCUTS or ANGLE missing!
N1745 Access denied
N1749 Incorrect number for FN17/FN18
N1749 Incorrect number for FN17/FN18
N1750 PLC: error in module call
N1789 Tool locked
N1790 Wrong range cycle
N1791 Point spacing too large
N1792 Wrong axis for line
N1793 Wrong axis for column
N1794 Wrong angular axis
N1795 Incorrect axis in range cycle
N1796 Incorrect line spacing
N1797 Range cycle not yet defined
N1798 Range beyond limit switch
N1799 Clearance height too small
N1807 Illegal file name
N1809 M114 not permitted with M116
N1810 System memory overflow
N1845 Update the system data!
N1848 Directory not empty
N1850 Cycle 4(G75/G76): incorrect axis
N1851 M130 not permitted
N1852 M130 not permitted with M114
N1853 M130 not permitted
N1854 M130 not permitted with comp.
N1855 No fixed cycle defined
N1856 Reciprocation feed rate missing
N1857 Tool radius too large
N1892 FN20/D20: incorrect condition
N1900 Device busy
N1901 Drive not found
N1914 Tool broken
N2039 Incorrect datum number
N2040 Insufficient slot width
N2041 Pocket too small
N2042 Q202 not defined
N2043 Q205 not defined
N2044 Q218 must be greater than Q219
N2045 CYCL 210 not permitted
N2046 CYCL 211 not permitted
N2047 Q220 too large
N2048 Q222 must be greater than Q223
N2049 Q244 must be greater than 0
N2050 Q245 must not equal Q246
N2051 Angle range must be under 360°
N2100 Wrong pallet
N2101 PLC:\NCMACRO.SYS missing!
N2102 'PALETT' in NCMACRO.SYS missing
N2103 Pallet data missing
N2186 Tilt plane: tool axis missing
N2211 No TOOL CALL permitted with M128
N2212 M91/M92 not permitted with M128
N2213 MP75XX not defined
N312 Height axis not permitted here
N2222 File not found in OEM.SYS
N2223 Incorrect file type
N2224 Field name not found
N2225 File empty
N2226 Material table not found
N2227 Cutting-material table not found
N2228 No material selected
N2229 WMAT-TMAT combination missing
N2230 No cutting data table selected
N2231 Block not permitted with M112
N2232 Correct the error block
N2233 FK blk not selectable with GOTO
N2238 Q223 must be greater than Q222
N2243 ANGLE in TOOL.T too small
N2253 Switch off external dc voltage
N2254 Normally closed relay open?
N2255 Switch on external dc voltage
N2273 TS: inadequate consistency
N2284 Parallel operation not possible
N2285 Axis locked
N2288 Tool holder defective!
N2300 Check the cutting data !
N2315 Q214: 0 not permitted
N2316 PLC: Event file not found
N2317 PLC: Too many events
N2319 TOOL TYPE table not found
N2320 CDT path not found
N2321 Too many *.CDT files
N2336 Safe input %d contradictory
N2339 No connection to network
N2342 FN17: Assignment value illegal
N2344 Enter the element.
N2345 Tool not defined
N2375 M112 not permitted with M128
N2377 S: Limit switch %.2s+ traversed
N2378 S: Gross positioning error L %.2s
N2377 S: Limit switch %.1s- traversed
N2384 All elements deleted!
N2385 Mandatory field deleted!
N2386 Max. line length exceeded!
N2387 Error during conversion!
N2500 Use RESTORE POS. AT N
N2504 Traverse direction not defined
N2505 No datum table active
N2506 Position error: center in axis 1
N2507 Position error: center in axis 2
N2508 Hole diameter too small
N2509 Hole diameter too large
N2510 Stud diameter too small
N2511 Stud diameter too large
N2512 Pocket too small: rework axis 1
N2513 Pocket too small: rework axis 2
N2514 Pocket too large: scrap axis 1
N2515 Pocket too large: scrap axis 2
N2516 Stud too small: scrap axis 1
N2517 Stud too small: scrap axis 2
N2518 Stud too large: rework axis 1
N2519 Stud too large: rework axis 2
N2520 Meas. cycle: length exceeds max
N2521 Meas. cycle: length below min
N2522 TCHPROBE 426: length exceeds max
N2523 TCHPROBE 426: length below min
N2524 TCHPROBE 430: diameter too large
N2525 TCHPROBE 430: diameter too small
N2609 M128 not permitted with 3DROT
N2610 M114 not permitted with M128
N2611 M128 not permitted with RR/RL
N2617 No measuring axis defined
N2618 Format error in date or time
N2621 M128: DATUM setting not allowed
N2635 Tool breakage tolerance exceeded
N2636 Cancel radius comp. before M128
N2642 Inverter not ready
N2644 M120: LOOK AHEAD not possible
N2645 Clear.hgt. Q260 < Meas.hgt. Q261
N2646 MC machine key depressed
N2647 Relay: n.c. contact closed?
N2655 Current to spindle not equal 0
N2657 Current to axis %.2s not equal 0
N2662 Begin/end block not markable
N2663 Insertion not possible here
N2664 Intermediate memory empty
N2665 Nothing is marked
N2668 Correct the block format
N2691 LN: Oriented stop not possible
N2692 M128 with LN block not possible
N2700 Test of cutout channels inactive
N2711 Safe checksum erroneous
N2733 To many columns
N2734 No axis column selected
N2735 M128 not permitted
N2736 No .TAB file open?
N2737 TAB: Field name too long
N2738 TAB: Field not numerical
N2739 TAB: Too many field names
N2745 Incorrect reference position %.2s
N2746 Incorrect entry in MP%u
N2747 Line is write-protected
N2748 Meas. cycle: M114 not permitted
N2749 Meas. cycle: M128 not permitted
N2750 M114, M128, 3DROT not permitted
N2752 MP: contradictory input
N2757 Command buffer overflow
N2758 Commands do not agree
N2760 FS function not performed
N2768 MC handwheel permissive key pressed
N2769 Incomplete cycle was deleted
N2770 Intermediate memory empty
N2771 No permission to write
N2772 To delete entire context: NO ENT
N2773 Impermissible change of context
N2774 No polar coordinates possible
N2775 To change context: press ENT
N2776 Input as context not permitted
N2777 Check parentheses for pairs
N2820 MC pos. deviation too large %.2s
N2824 Calibrate TT in tilted plane
N2825 Calibrate TT in non-tilted plane
N2826 TT not parallel to tool axis
N2827 Faulty braking process %.2s
N2828 Position control time too short
N2829 Enter Q247 unequal 0
N2830 Enter Q247 greater than 5
N2834 EnDat defective %X %.2s
N2837 FK block was not converted
N2849 Switch on spindle
N2853 Synchronization monitoring %.2s
N2858 No testing rights
N2868 TT: Pre-position the axes
N2945 M91/M92 not permitted
N2969 Required value missing
N2993 Internet address error
N2995 Illegal PLC datum shift
N2996 Trav. range shift not permitted
N3002 Special spindle mode not allowed
N3006 Perform a tool change!
N3012 M120 LA not permitted
N3013 Circular interpolation illegal
N3025 Pallet line locked!
N3026 Radius compensation not possible
N3055 Enter direction Q351 unequal 0
N1149 Incorrect entry in MP%.4u
N958 Relay ext. dc voltage missing
N1182 Incorrect entry in MP%.4u.%u
N3063 3DROT: No description found
N3065 Reset M114, M128 or CYCL19
N3081 Thread depth too large
N3187 No PNT file selected
N3188 PNT: Clearance height too low
N3189 CYCL CALL PAT not permitted
N3192 Missing calibration data
N3193 Tolerance exceeded
N3199 Spindle switching not permitted
N3205 Autostart not enabled
N3206 No macro %.20s
N2720 MC amplitude too high %.2s
N44 MC amplitude too low %.2s
N45 MC frequency too high %.2s
N2687 MC NC temperature out of tol.
N2612 MC S input %d not equal 0
N14018 MC standstill monitoring %.2s
N57 CC limit switch %.2s-
N55 CC limit switch %.2s+
N3214 Table values were changed
N3218 PLC function not permitted
N3220 Tolerance in MP6510 too small
N3221 Calibration radius too large
N3231 PAL/PGM field is missing
N3232 Language load error %d
N3234 Tool preselection is running
N3235 Negative feed rate
N3236 Switch-off pos. %.2s unequal ENDAT
N3239 Selected software not loaded
N3243 No tool axis programmed
N3245 M function not permitted
N3354 Function not permitted
N3356 Kinematic table defective
N3357 MP subfile incorrect
N3441 M144 not permitted
N4957 Contradictory entry
N3532 Incorrect entry in MFUNCT.TAB
N3927 Probing not permitted
N3928 M112 not permitted with M144
N4175 Pallet line with completed part
N4176 Fixture change macro missing
N4177 Invalid geometry context
N4197 Mid-program startup active
N4276 ORIENTATION not permitted
N4491 Mid-program startup not possible
N4492 MC: Machine permissive button depressed
N4571 Check the depth sign
N4572 Entry character not allowed
N4573 Lowercase letter not allowed
N4574 Letter not allowed
N4575 Numeral not allowed
N4880 Insufficient system memory
N4881 PLC program not found
N4882 M140 not permitted
N4903 Radius oversize not allowed
N4905 Processor 1 temperature too high
N4906 Processor 2 temperature too high
N4935 Actual position saved %.2s
N5073 LSV2: Line interrupted
N5074 LSV2: Transmission error
N5075 LSV2: Transmission error
N5076 LSV2: Transmission error
N5077 LSV2: Timeout error
N5078 LSV2: Transmission error
N5079 LSV2: Timeout error
N5080 LSV2: Timeout error
N5081 LSV2: Outgoing transmiss. error
N5099 MC no memory available
N5225 Incorrect software version
N5228 Feed rate = 0 not allowed
N5236 TNC temperature warning %d°C
N5242 PLC program not compiled
N204 TNC temperature too high %d°C
N5286 Error: Profibus configuration
N5287 Profibus: Hardware error
N5288 Profibus: Error initialization
N5312 Nonvolatile PLC data deleted
N5338 Soft-key project not translated
N5366 Line insertion not allowed
N5367 T %u in line %u already assigned
N5368 LBL %u in line %u already assigned
N5369 No axes selected
N2612 CC%d S input %d not equal 0
N2687 CC%d NC temperature out of tol.
N2688 CC%d +5V out of tolerance
N5434 Function not available
N5479 Magazine rules not translated
N5484 Axis angle not equal tilt angle
N5566 No reference system change!
N5567 MC wrong quantity FS-CC
N5568 Too many characters
N5569 Value out of input range
N5570 Too many decimal places
N5571 Algebraic sign not allowed
N5572 Only integers permitted
N5573 Q not allowed: enter a number
N5574 Incremental input not allowed
N5575 Too many M functions
N5576 Too many axes programmed
N5577 Axis double programmed
N5578 Element double / not allowed
N5579 Incomplete data input
N5580 ISO: Block number N missing
N5581 Required element missing
N5582 Syntax incorrect
N5583 No measured value saved %.2s
N5617 Keyword unknown
N5618 Syntax element not editable
N5619 PGM header not editable
N5627 Set MP1356.%d to %.4f
N5628 Too many axes programmed
N2652 CC%d inverter for spindle RDY=0
N2653 CC%d inverter for axis RDY=0
N2654 CC%d inverter for spindle RDY=1
N2656 CC%d inverter for axis RDY=1
N2743 CC%d FS checksum error
N2759 CC%d command not acknowledged
N2819 Faulty data from CC%d
N2821 No pos. values from the CC%d
N2822 CC%d no pos. values from the MC
N2823 MC/CC%d checked axes unequal
N2831 CC%d wrong include-file version
N5097 CC%d SH1=0
N5096 CC%d SH1=1
N2743 MC S checksum error
N5631 MC command %3d not acknowledged
N5632 MC and CC mismatch
N5635 Channel %d cannot be displayed
N5641 MC safety doors are open
N5651 Tool axis is missing
N5655 Axis %.2s started w/o test by MC
N5671 Check the position encoder %.2s
N5672 Use preset table!
N5673 Q303 in meas. cycle undefined!
N5693 Tool axis not allowed
N5699 Calculated values incorrect
N5700 Contradictory measuring points
N5709 Circle data error
N5712 Password not found
N5713 No password supplied
N5714 Password too long
N5715 Password already encrypted
N5757 Preset setting: Axis locked!
N5759 Incorrect clearance height!
N5969 Really delete NC block? DEL!
N5970 Axis letter not permitted
N5971 Cannot cancel Block Skip
N5972 String incomplete
N6018 Double referencing is active
N6027 Wrong axis programmed
N6049 PET table: Too many lines
N6052 Contradictory plunge type!
N6055 This fixed cycle not allowed
N6066 Rotary axis tolerance illegal
N6069 MC PWM output is not present
N6072 Cannot go past edge of screen
N6079 M128 not allowed
N6080 M144 not allowed
N6081 MC SOM 4 not possible
N6082 MC operating mode not possible
N6086 Error while saving monitor list
N6087 Error while opening monitor list
N6088 Error while opening TEMP.WLT
N6089 Last monitor list is missing
N6090 Selection list not found
N6091 Selection list is empty
N6094 Incorrect code number
N6093 No safe axes/spindle
N6099 Value invalid
N6100 Operand invalid
N6101 MC SOM 4 not released
N6102 Column must not be changed
N6103 Preset number does not exist
N6105 MC SOM 2 only one axis allowed
N498 File %.27s is missing
N206 PGM %.28s not found
N6118 MC SOM 4 Press the permissive key
N6182 Profibus: Configuration error
N6183 Profibus: PCI hardware error
N6184 Profibus: file/memory error
N6187 Excessive subprogramming
N6188 Excessive subprogramming
N6189 5-V power supply too high
N6190 5-V power supply too low
N6193 Spline starting point incorrect
N6212 Actual pos. capture not possible
N6236 The PLC program has been stopped
N6264 Program-run graphics impossible!
N6291 Reference the spindle!
N6294 Safe MP changed by PLC
N6307 T%s: Remaining tool life too short
N6308 Tool %s not defined
N6309 Data trans.: illegal characters
N6312 MP subfile missing
N6408 MP subfile incorrect
N6409 PLC strobe not allowed (%s)
N6410 PLC strobe illegal in cycle %d
N6411 Limit switching not allowed
N6412 Preset saving not possible
N6413 Kinematic change not possible
N6414 block scan inconsistent %s
N7222 Line is write-protected
N7784 Error while writing to table
N7799 MC brake test not completed
N7800 +24 V MC short on brake line
N7801 0 V MC short on brake line %.2s
N7803 Set the datum by soft key!
N7815 Machine not initialized
N7922 Supply voltage missing at X44
N7923 MC tool mag AutoStart impossible
N7935 Binary file on external drive
N7936 Target directory is source dir.
N7937 Target file is source file
N7938 MP2257.%d incorrect (ID=$%08X)!
N7964 TCPM: Contradictory vector!
N7969 Application %s cannot be started
N7971 Process cannot be run
N7972 Target device does not exist
N7973 File cannot be renamed
N7974 File type cannot be changed
N7975 No space left on drive
N7977 File system I/O error
N7978 File access canceled
N7979 Too many files open
N7980 Line/block too long
N7981 File does not exist
N8001 No real-time application active
N8002 Error in real-time application
N8005 Context change only on initiat.!
N8032 LSV-2: Too many connections
N8043 Compilation not allowed
N8044 PLC binary file selected
N8049 Dependent file write-protected
N8071 Cannot switch window!
N8072 Read-only section file!
N8090 Reciprocating not possible!
N8110 NC program aborted
N7798 System error %d
N8114 0x01 Function not recognized
N8115 0x02 Function already started
N8116 0x03 Controller is not active
N8117 0x04 Controller is active
N8118 0x05 Pulse is too large
N8119 0x06 Unknown parameter
N8120 0x07 Error reading DAC values
N8121 0x08 Serial EEPROM: No acknowledgment
N8122 0x09 Serial EEPROM: SDA hanging on 0 or 1
N8123 0x0A Data missing
N8124 0x0C Function locked
N8125 0x0D Wrong operating mode of TNC
N8126 0x10 Undefined error (see error buffer)
N8128 DSP command string too long
N8129 No data received
N8130 Faulty data received
N8131 No measurement data available
N8132 Undetermined cause of error
N8133 Mach. param. for drive controller not available
N8134 Unsupported motor type
N8135 No HEIDENHAIN power module
N8136 Incorrect controller unit
N8140 Message not defined
N8141 Message unexpected
N8142 Error message from drive contrlr
N8213 Entry value incorrect
N499 File %.27s is missing
N8231 FUNCTION TCPM is not possible
N8284 Entry for elec. ID label missing: %s
N8290 Working space limit exceeded
N8292 PL 510 supply voltage missing
N8293 Short circuit at PL 510 output
N8401 PLC module %d unknown
N8494 CC%d timeout version comparison
N8495 CC%d timeout SMP check sum
N8591 PLANE fct.: TURN not allowed!
N8643 CYCL CALL POS block incomplete
N8644 Increm. programming not allowed
N8658 Set datum in all axes
N8757 MC 422B fan defective
N8758 This EnDat OEM version is not supported.
N8892 Coupling function not possible
N502 Direction of rotation missing
N503 Rounding arc radius too large
N504 Contradictory entry
N505 Insufficient contour definition
N506 FPOL missing
N507 TNC program block not permitted until contour is resolved
N508 The contour is resolved: select block is not permitted
N509 End of closed contour: no incr. coordinates permitted
N510 Rounding arc or chamfer not permitted at this point
N511 Rounding/chamfer with tangential transition is not permitted
N512 Straight line before or after rounding/chamfer has 0 length
N513 Chamfer is possible only between two straight lines
N514 Chamfer too large
N515 Path comp incorrectly begun: NC block must be a straight line
N516 Path comp incorrectly ended: NC block must be a straight line
N517 Contour too complex. More data needed
N518 FK: arithmetical error
N519 FK block not permitted at this point
N522 Reference to specified block not permitted
N523 Reference to CC block not permitted
N525 Auxiliary point requires both coordinates
N526 Parallel operation of FK graphics not possible
N527 Blank form too large
N528 Window too large
N529 Window too small
N530 Window cannot be shifted farther
N9785 Direction cannot be distinguished because no movement could be detected.
N10248 NC function not allowed
N10521 Starting time has passed
N10664 Tool usage file locked
N10665 Programming graphics impossible
N10672 SPAWN/SUBMIT is blocking a context switch
N10710 PROFIBUS inputs were not updated.
N10711 PROFIBUS inputs were not updated.
N10942 Incomplete display
N10949 Stepover is too small
N10950 Overlap factor too large
N11044 Cylinder radius 0 not permitted!
N11045 Queue overflow: %s
N11114 System error
N11115 System error
N11116 System error
N11117 System error
N11232 Cannot switch modes of operation
N11275 File type missing or incorrect
N11391 Key is locked
N11410 Global Q parameter not defined
N11411 Global Q param. doubly defined
N11412 Global parameters missing
N11413 smarT.NC not possible
N11442 Two rotary positions not allowed
N11453 File name already exists
N11454 Program header already exists
N11559 M120: LOOK AHEAD not possible
N11574 M114 without machine geometry
N11575 Axis geometry not defined
N11576 Rotary-table coordinates missing
N11577 No kinematics defined
N11578 Angle cannot be calculated
N11579 Kinematic table missing
N11580 Activate 3DROT
N11581 PLANE function not possible!
N11582 CC%d : Program %s cannot start
N11585 PLC strobe not allowed (M%d)
N11586 Test graphic not possible
N11588 PGM being edited in smarT.NC
N11589 PGM being edited in parallel
N11593 No option for controller unit
N11595 File deletion impossible
N11597 Interference on PL interface
N11598 PLC partition: Not enough memory
N11601 CC%d: TIMEOUT CMD=0x%02X
N11750 File does not exist
N11751 Select file again!
N11752 Label name already assigned
N11753 Label name already assigned
N11754 Label name not found
N11755 Label name in line %u is taken
N12214 USB device cannot be removed
N12215 USB device removed w/o being closed
N12283 Point angle not defined
N12284 Contradictory data
N12358 CANCELLATION in block %u (%u %%)
N12759 Tree view buildup canceled
N12760 MC housing fan defective
N12767 Reentrance impossible
N12768 Too many units programmed
N12770 3,3-V power supply too high
N12771 3,3-V power supply too low
N181 Blank form definition incorrect
N520 FCT or FLT block not permitted at this point
N521 Incremental angle reference not permitted here
N524 For FPOL give both coordinates
N12822 Function could not be concluded (timeout).
N12823 Enter tool radius greater than 0
N12824 More than 5 axes in PLC positng.
N12830 Slot position 0 not allowed!
N12837 Contour subp.: Only 1 axis pgmd.
N12857 Permiss. program length exceeded
N6091 No symbolic programming
N13066 Preset saving not possible
N13072 Datum setting not allowed
N13147 PLC program is not running
N4 Processor check error 3
N9 Processor check error 8
N11 Processor check error A
N12 Processor check error A
N14 Processor check error A
N16 Processor check error B
N19 Processor check error E
N29 Processor check error O
N33 Checksum error A
N34 Checksum error B
N40 Movement monitoring error in %.2s A
N43 Dif. in position <> shaft speed too high in %.2s
N13741 Line %d: Semicolon (;) missing
N13742 Line %d: Too many keywords
N13743 Line %d: Incorrect keyword
N13744 Line %d: Command unknown
N13745 Line %d: Format statement incorrect
N13746 Line %d: Format statement incomplete
N13747 Line %d: Keyword too long
N13748 Line %d: Index missing
N13749 Line %d: Closing bracket (]) is missing after index
N13750 Mask file not found
N13751 Control cannot make output file
N13154
N13155 Collision warning acknowledged
N13156 Profibus firmware obsolete
N13302 MPFRAGMENTFILE does not exist
N13340 Entry value incorrect
N13348 DHCP: Input not allowed
N13381 Column reset not allowed
N13387 Enter an infeed not equal to 0.
N13475 Function not permitted!
N13476 Clipboard is empty!
N13477 MC braking control defective
N13478 MC braking control defective %.2s
N13486 Shaft speed outside range limits %d%%
N13487 USB: TNC does not support device
N13752 Editing not allowed
N13753 TOOL.T: Number teeth defined=0
N13758 M118 not allowed
N13761 No editing allowed
N13769 Open-loop axis %.2s: Standstill
N13816 Function not permitted
N13825 Function not enabled
N13827 Erroneous DXF file
N13838 Auto. keyboard lock was opened
N13945 Function not permitted
N13957 No editing allowed
N13958 M136 not allowed with FU/FZ
N13960 smarT.NC not allowed
N13961 Incremental input not allowed
N14017 Switchover of Q399 not allowed
N14019 CC%d current measurement timeout
N14020 MC: Incorrect safe op. mode
N14022 CC: Machine key depressed
N14023 MC: Mach. permiss. button depr.
N14024 CC: Mach. permiss. button depr.
N14025 CC: Handwheel permissive button depressed
N14026 CC: Machine permissive button depressed
N14027 CC: Protective doors are open
N14032 Calculated coordinate too large
N14156 No tool axis defined
N14253 Caution: Prepos. height defined!
N14254 MC permissive button depressed
N14255 CC permissive button depressed
N14299 Program conversion not possible
N14434 Faulty range definition!
N14479 No datum table selected
N14486 M140 MB MAX not allowed
N14487 Max. string length exceeded
N14518 Tool number not allowed
N14519 Tool name not allowed
N14520 Division by 0 not allowed
N14521 Root extraction not allowed
N14522 Logarithm not allowed
N14523 Tangent not allowed
N14525 Function locked by FCL
N14550 Arc cos: Abs.val. greater than 1
N14551 Arcsine: Abs.val. greater than 1
N15439 M128: Preset editing not allowed
N15465 No data available!
N15466 File missing or incorrect
N15491 LSV2: Breakpoint not allowed!
N15614 No probing direction defined
N15658 Speed S > than NMAX of TOOL.T
N15672 Drive cannot be renamed!
N15673 Drive cannot be copied!
N15674 Drive cannot be deleted
N15675 TNC cannot open the file type!
N15687 MC movement monitoring %.2s
N15688 MC error in braking process %.2s
N15691 GOTO function not allowed!
N15766 Tool axis not allowed
N15767 Traverse was outside of permissible range %.2s
N15923 PLC memory layout has changed
N15967 The help system cannot be called
N15973 M141 not allowed
N16007 Parallel operation not possible
N16010 Operator safety module not supported
N16198 PLC memory layout could not be initialized
N16362 MC inverter RDY=0 %.2s
N16363 MC inverter RDY=1 %.2s
N16407 Data transfer not possible
N16408 Axes cannot be swapped.
N16409 Axes cannot be swapped.
N16410 Axes cannot be swapped.
N16411 Input limit exceeded
N16412 No editing allowed
N16413 Undefinable error
N16561 AFC: Spindle overload
N16563 Position encoder %.2s: Amplitude too high
N16564 Position encoder %.2s: Amplitude too low
N16565 Position encoder %.2s :Frequency too high
N46 Position encoder %.2s defective
N16586 PLANE AXIAL not allowed
N16593 MC braking test not activated
N16623 Table definition incorrect
N16718 Spindle speed out of tolerance range %.2s
N16798 Global PGM settings deactivated
N16800 smarT.NC: File type not allowed
N16830 No editing while PGM is running
N17063 TNC cannot process the macro!
N17161 ENDAT interpolation not possible %.2s
N17162 Request for electronic ID label not possible
N17163 Error in TRC compensation %.2s
N17167 'AFC' in NCMACRO.SYS missing
N17207 MC: Incorrect S operating state
N17384 Not enough main memory
N17386 Pallet operation not allowed
N17387 M128 not allowed
N17390 PLANE funct.: MOVE not possible
N17662 Active traverse range incorrect
N17663 DCM: Status settings incorrect
N17735 MC nominal-to-actual position error too large %.2s
N17938 EnDat connection not possible
N18060 3DROT not permitted
N18075 MC 1st violation of limit switch %.2s+
N18076 MC 1st violation of limit switch %.2s-
N18145 Called PGM was changed
N18146 Multiple marking not allowed
N18147 Function for file, not directory
N18148 PGM protectn. not set/cancelable
N18149 File type protected by MP
N18150 OPEN WITH not allowed
N18156 USB device cannot be removed
N18157 No USB device marked
N18220 PL configuration incorrect
N18280 %s
N59 FN 14: error code %s
N18303 CC%d inverter for axis RDY=0 (safety relay)
N18304 CC%d inverter for axis RDY=1 (safety relay)
N18325 MC S software error %d
N18371 MC start test of the cutoff channels not possible
N18401 Internal error while copying!
N18629 Software option not active
N18630 Kinematics cannot be restored
N18631 Function not permitted
N18632 Contradictory workpc. blank dim.
N18861 HSCI: Hardware error
N18862 HSCI: Error initialization
N18891 M91 or M92 not possible
N18903 Semifeedforward not permitted
N18904 Directory does not exist
N18912 CC%d inverter for spindle RDY=1 (safety relay)
N18913 CC%d inverter for spindle RDY=0 (safety relay)
N18914 Cycle generation is defective
N18915 HSCI: IOC file not found
N18928 M128 not allowed!
N19236 LSV2 transfer interrupted!
N19292 No reference power recorded
N19293 TOOL.T: too many teeth
N19398 Measuring position not allowed
N19411 PLC program could not be started
N19440 M function macro not allowed
N19448 DCM: Tool status unknown
N13827 Application 'DXF_CONVERTER' cannot be started
N19501 Error during self test
N19502 Timeout during self test
N19503 Communications error during self test
N19504 Unknown error during self test
N19754 Emergency stop from SPLC
N19755 Fatal error from SPLC
N19764 Tool deletion is not allowed
N20418 Self test is deactivated
N20457 MC: System error in SPLC-RTS
N20458 Faulty recognition of PL/MB hardware
N20459 HSCI-PL/MB reports error
N20460 HSCI-PL/MB reports error
N20461 MC: System error in SPLC-RTS
N20462 MC: System error in SPLC-RTS
N20463 Run-time error in SPLC program
N20464 SPLC cannot load program
N20465 SPLC program has changed
N20466 SPLC program cannot run
N20467 Machine not in safe operation
N20469 Configuration of SPLC inputs
N20471 Configuration of SPLC inputs
N20473 Configuration of SPLC cycle time
N20477 Python script already started
N20481 Kinematic access not possible
N20482 Meas. pos. not in traverse range
N20483 Preset compensation not possible
N20639 Pocket table is write-protected
N20650 Keystroke sequence rerun ended
N20661 Rotation not permitted
N20662 Scaling factor not permitted
N20663 Mirroring not permitted
N20664 Datum shift not permitted
N21084 Place handwheel in charger
N21096 Preset with offset active
N21097 Tool radius=0: DCM not possible
N21144 Handwheel: M91/M92 not allowed
N21219 ACCESSLEVEL: Function locked
N21232 Override potentiometer?
N21233 Tool-carrier kinematics missing
N21254 Test program cannot be opened
N21255 Test program cannot be generated
N21256 Test program cannot be run
N21257 DCM: Clamping fixtures inactive
N21258 File does not exist
N21260 SPLC program not configured
N21261 SPLC time-out in MC
N21426 DCM: Ambiguous collision objects
N21675 Unsafe control software
N21701 Line deletion not allowed
N21712 Switch-off process not possible
N21948 MC Incorrect command from the MC
N21949 Rapid traverse configured incorrectly
N21932 MC timeout during braking %.2s
N22055 Parallel operation not possible
N22060 MC traverse range exceeded at SS2 %.2s
N22077 MC change from SOM_2/SOM_3 to SOM_4 not possible
N22077 MC change from SOM_4 to SOM_2/SOM_3 not possible
N22079 Insufficient RAM
N22124 MC SPLC requests invalid stop reaction
N22125 MC SPLC requests invalid safety function
N22266 SPLC program not translated
N22330 M94 not possible
N23611 Pocket table locked
N2187 Axis alarm %.2s
N23636 MC brake cannot be deactivated %.2s
N23720 No umlauts allowed!
N23756 Fct. only allowed for rotary axes
N23767 No editing allowed
N23768 QR parameters not restorable
N23784 MC Invalid SPLC operating mode
N23830 HSCI/Profibus: Configuration error
N23832 MC axis group configured incorrectly %d
N23835 Error in self test
N7798 CC%d error %d %d %d
N7798 CC error %d %d %d
N23945 MC System clock MC is not equal to SKERN MC
N23946 MC System clock MC is not equal to SPLC MC
N23947 MC System clock MC is not equal to SPLC CC
N23949 Tool radius too large
N23950 Plunging type is not possible
N23951 Plunge angle incorrectly defined
N23952 Angular length is undefined
N23953 Slot width is too large
N23960 MC error during cross comparison:  %s
N23961 MC Safe output is not equal:  %s
N23967 Designation not found
N23993 Parameterization error in Python script
N24013 MC +3.3V out of tolerance
N24014 MC +3.3VPIC out of tolerance
N24015 MC +12V out of tolerance
N24016 MC speed of fan 1 too slow
N24017 MC +5V out of tolerance
N24024 Tool data inconsistent
N24074 MC fan not recognized
N24075 MC speed of fan 2 too slow
N24128 MC actual-value measuring error %d %.2s
N24130 MC axis %.2s in servo control
N24131 MC spindle %.2s in servo control
N24188 Changed NC software version
N24189 Error in SPLC configuration data
N24191 MC excessive deviation of actual/nominal speed %.2s
N8127 Unknown LSV2 error: %x
N24360 Incorrect condition of safe output %s
N24394 Level undefinable
N24438 File content is faulty
N24484 Faulty assignment of tool/cut no.
N24515 No start allowed in emergency stop
N24585 MOVE not possible
N24586 Block format incorrect
N24592 SPLC program has changed
N24594 SPLC program binary code of MC has changed
N24596 SPLC program binary code of CC has changed
N24860 MC: Erroneous data from SPLC %s
N24959 Presetting not allowed!
N24967 MC limit switch %.2s+
N24968 MC limit switch %.2s-
N24972 Safe Torque Off (-STO.B.x) is active
N24973 External emergency stop
N24974 MC S input signals %d not equal
N24975 MC feed rate greater SLS %.2s
N24976 CC feed rate greater SLS %.2s
N24977 Op. state of MC not equal CC
N24979 MC speed greater than SLS %.2s
N24980 CC speed greater than SLS %.2s
N5097 MC -SMC.A.WD=0
N24981 MC: Incorrect safe axis group
N24983 Axis not at test position
N25030 MC S status reaction is active: %s
N25031 Wiring of SPLC input %d
N25033 Wiring of emergency stop
N25160 MC SMC Autotest software loaded
N25237 Wrong input %s for dynamic test
N25243 Gliederung widersprüchlich
N25250 Konfiguration SPLC-Eingänge geändert
N25267 Radius negativ: Kein DCM möglich